Soil pH is a measurement the alkalinity or acidity of soil. pH is measured on a scale of 1-14, with 7 as the neutral mark, anything below 7 considered acidic and anything above 7 considered alkaline.
Refers to the attraction between two molecules, each having regions of low level positive and negative charge.
A dimpled membrane, typically manufactured using a high density polyethylene, impermeable to water and water vapor, that creates an air gap between the membrane and a foundation wall. Water between the air-gap membrane and the foundation wall flows freely towards the weeping tile. It also provides a capillary break between the foundation wall and the saturated soil surrounding it.
The replacement of excavated earth into a trench around or against a basement or crawlspace foundation wall.
Basement Floor Slab
The 4 or 5 inch layer of concrete that forms the basement floor.
Mold Exposure – Black Mold – Toxic Mold – People are exposed to mold through the air they breathe, contact with skin, and ingestion. Molds need moisture, a food source, time, and to be left undisturbed. Any source of moisture within an indoor environment can be a possible contributor to a mold problem and poor indoor air quality. It has been stated simply that the best mold control, is moisture control. Many molds given the right conditions have the potential to cause ill health effects in susceptible individuals.
When outside pressure exceeds the design capacity of a wall resulting in a bow or curve.
A reinforced polymer that is characteristically very strong, light and a composite material known for its high strength to weight ratio. Carbon Fiber will not stretch or bend over time making it perfect for reinforcing concrete walls.
Carbon Fiber Staples
Carbon Staples can be used as a crack control stitching system designed to transfer load away from repair materials.
Carbon Fiber Kevlar Weave
This carbon fiber product has a Kevlar weave that produces some horizontal strength. A necktie is attached to the sill plate, which can disperse the outside force.
Carbon Fiber Plates / Sheets
Carbon fiber plates that are pre-pregnated with an epoxy resin. The plates do not secure to the sill plate or floor where the major problem areas occur.
A barrier that prevents the flow of moisture through the small interconnected pores in concrete due to adhesion and surface tension. Also referred to as “wicking.”
To install or apply a sealant across or into joints, cracks, or crevices to prevent the passage of air or water.
A pre-fabricated structural component constructed of concrete and cinders that is utilized to construct foundation walls, retaining walls, etc.
Clay Bowl Effect
Backfill soil that’s been removed as the foundation is dug is looser, more porous and much more absorbent of water than the unexcavated soil around it. As the soil around the house settles, it begins to dip lower than the unexcavated soil. As the water runs downhill into this depression, it pools and absorbs into the dirt around the foundation. In areas where the soil contains clay, this is called the “Clay Bowl” effect which allows water to seep anywhere it can go resulting in pressure on basement walls. This pressure can create cracks that can allow water to come through.
Soil, which is composed of very fine particles, usually silicates of aluminum and/or iron and magnesium. Clay soil impedes the flow of water, meaning it absorbs water slowly and then retains it for a long time. Wet clay soil is heavy and sticky, and tends to swell from the added moisture. When dry, clay soil shrinks and settles. The top layer can bake into a hard, concrete-like crust, which cracks.
The replacement of excavated earth containing clay around a basement foundation wall. Clay backfill can result in poor surface and subsurface drainage leading to water ponding around the house, leakage of ground water through the basement or crawlspace walls, and structural damage to the foundation.
Cold Joint or Cold Pour
An unplanned joint or discontinuity in poured concrete structures resulting from a delay in placement of sufficient time to preclude a chemical union of the material in two successive pours.
Large, rectangular blocks used in construction usually made from sand and fine gravel. The use of block work allows structures to be built in the traditional masonry style with layers (or courses) of overlapping blocks. American homes are typically built with a concrete foundation and slab with a concrete block wall on the perimeter.
A formed, sawed, or tooled groove in a repair surface to create a weakened plane and regulate the location of cracking resulting from restrained contraction of the material. Such provisions are also termed control relief joints. Adequately designed and constructed, these joints serve to eliminate random surface cracks by gathering, distributing and dissipating stress forces resulting from temperature and moisture variations.
A cold joint is the intersection between the end of one concrete pour and the beginning of a new pour. The basic rule is to try to avoid cold joints by pouring straight through until the job is finished. The cold joint is a weak area and could allow the entry of water.
A crawl space (as the name suggests) is a type of basement in which one cannot stand up — the height may be as little as a foot, and the surface is often soil. They offer access to pipes, substructures and a variety of other areas that may be difficult or expensive to access otherwise. While a crawl space cannot be used as living space, it can be used as storage, often for infrequently used items. Health and convenience issues accompany a crawl space as water from the damp ground, water vapor (entering from crawl space vents), and moisture seeping through porous concrete can create a perfect environment for mold/mildew to form on any surface in the crawl space, especially cardboard boxes, wood floors and surfaces, drywall and some types of insulation.
Crawl Space Encapsulation
The process of encapsulating the crawl space with a vapor barrier and insulation creating a clean, healthy and usable space.
Treatment of a surface or installation of a technology to resist the passage of moisture caused by differences in moisture content, vapour pressure and temperature across the basement envelope to prevent accumulation of water against the outer surfaces of the envelope (walls and floor slab).
A household appliance that reduces the level of humidity in the air.
With respect to concrete block foundations, involves the removal or draining of water that has accumulated within concrete blocks.
Dig & Push
A method in repairing a bowed foundation wall by excavating soil against the wall from the outside and applying pressure to push the wall back to a straight position. The area outside is then backfilled with gravel.
A vertical pipe used to drain rainwater from a roof.
The process associated with draining water.
A perforated, corrugated plastic pipe laid at the bottom of the foundation wall and used to drain excess water away from the foundation. It prevents ground water from seeping through the foundation wall. Sometimes called perimeter drain.
Vapor Barrier for Basements, Attics and Crawl Spaces.
Common interior building material comprised of plasterboard pressed between two thick sheets of paper. Drywall is easily damaged by exposure to water. It also supports the growth of mold due because it is porous.
A dry well is an underground excavated area filled with stone that disposes of water, most commonly drainage run off, by dissipating it into the ground, where it merges with the local groundwater. A hole in the ground filled with gravel or rubble to receive drainage water and allow it to percolate away.
A deposit of white salts left on a surface when a solution containing the salts leaches from concrete or masonry and then evaporates.
Code compliant and fire-escapable windows created for basements.
A method of sealing or repairing cracks in poured concrete by injecting epoxy adhesives into the cracks in order to fill them.
The wearing away of land or soil by the action of wind, water, or ice.
Evaporative Moisture Cooling
A phenomenon whereby moisture that evaporates imparts a cooling effect upon the material that is damp or wet.
Evaporative Moisture Cooling
A phenomenon whereby moisture that evaporates imparts a cooling effect upon the material that is damp or wet.
To dig out and remove, as earth.
Exterior Footing Drain
A tube or cylinder or box that is normally installed around the exterior perimeter of the foundation footings that collects and directs ground water away from the foundation of the house.
Masonry failures due to vertical shear.
Floor Drain Backwater Valve
A check valve that prevents the backflow of water from the municipal storm sewer system to your basement floor drain.
Horizontal supporting members that run from wall to wall, wall to beam, or beam to beam to support a floor. It may be made of wood, steel, or concrete.
A footing is a poured concrete structure embedded below the frost line, and is typically twice the width of the wall that it supports. The footing transfers the weight of the foundation walls to the soil or bedrock beneath it.
The lowest and supporting part or member of a wall, including the base course and footing courses; in a frame house, the whole substructure of masonry.
A French drain, drain tile, perimeter drain or land drain is a ditch covered with gravel or rock that redirects surface and ground water away from an area. A French drain can have hollow pipes along the bottom to quickly disperse water that seeps down through the upper gravel or rock. French drains are common drainage systems, commonly used to prevent ground and surface water from travelling towards the foundation.
Also referred to as frost depth or freezing depth — is most commonly the depth to which the groundwater in soil is expected to freeze. The frost depth depends on the climatic conditions of a given geographic area, the heat transfer properties of the soil and adjacent materials, and on nearby heat sources.
Glass Block Windows
An architectural element made from glass. Glass bricks provide visual obscuration while admitting light. Commonly used in basements for privacy and security.
This typically refers to the pitch of a slope such as a hill, road or railway; with respect to waterproofing, it is the height of the soil, or other surface, surrounding the foundation.
The movement of materials from one location to another by force of gravity.
Is water located beneath the ground surface in soil pore spaces and in the fractures of rock formations. Groundwater is water that has drained through surface layers of soil and rock until it reaches a layer of rock material through which it cannot pass, or can pass only very slowly. This results in the accumulation of water in the rock layers above this impermeable layer. The water is stored in gaps in the rock, or between the particles of which the rock is composed.
A crack in an exposed concrete surface that is barely visible because of its extremely narrow width.
Refers to voids in concrete caused by the mortar not filling the spaces between the coarse aggregate particles.
Typically means “a love of water”. In the context of polyurethane injection resins, a hydrophilic polyurethane is attracted to and dissolves well within water.
Refers to “a fear of water”. In referring to the properties of polyurethane and epoxy resins, the hydrophobic resin molecules cluster together upon exposure to water; similar to how cooking oils tend to cluster together even after they are dispersed.
The force that is exerted on an underground structure by the water that is in the ground surrounding the structure.
A fitting that goes on your sump pump discharge line. It helps to prevent ice backing up causing a basement to flood.
Interior Perimeter Drain
Refers to the installation of a perimeter drain pipe, that functions in a similar way to weeping tile, along the inside perimeter of the basement walls beneath the floor slab.
A non-destructive testing method for locating delaminations in pavements and bridge decks and detecting moist insulation, concrete, and wood in buildings; the presence of flaws within concrete affects the heat conduction properties of the concrete and the presence of defects is indicated by differences in surface temperatures when the test object is exposed to correct ambient conditions. In the waterproofing industry it is typically used to detect moisture behind closed walls by detecting evaporative moisture cooling (EMC).
A joint between the footing and foundation wall.
A layer of material, typically impermeable, used as a lining on outdoor concrete walls. See also, air-gap membrane.
Usually white in appearance, is the superficial growth of fungi on organic materials, such as wood. A plant disease where the pathogen occurs as a growth on the host’s surface.
The growth of minute fungi that form on organic matter, often the result of decay due to exposure to moisture/dampness. Parasitic, microscopic fungi (like Penicillin) with spores that float in the air like pollen. Mold is a common trigger for allergies and can be found in damp areas, such as the basement or bathroom.
A brick being secured to another similar brick or bricks by means of mortar or grout.
Negative Side Waterproofing
Applying waterproofing to the side of a structural element opposite the one subjected to hydrostatic pressure (always the inside wall surface).
Columns of concrete usually poured into drilled holes in the ground, on which the concrete slab will rest. This ensures that the slab is ultimately resting on the ground sufficiently solid to support the weight of the home.
A thermoplastic polymer used in a wide variety of applications. Used in crawl space encapsulation material.
A method for sealing or repairing cracks in concrete by injecting polyurethane resin.
Positive Side Waterproofing
Applying waterproofing material to the side of a structural element subjected to hydrostatic pressure (always the outside wall surface).
Any concrete structure or slab that was poured and formed in a liquid state.
A 13lb steel H-beam that is bolted into the floor using a bracket at the bottom. At the top is an adjustable bracket that supposedly allows you to move the wall back overtime.
A colourless, odourless, radioactive gas that occurs naturally as a result of the decay of radium. It is found to varying degrees as a component of soil gas and is known to enter dwelling units by infiltration into crawl spaces and basements. The presence of the decay products of radon in sufficient quantity can lead to increased risk of lung cancer.
Cracks at the corner of windows and other openings that are usually the result of stress build-up at the corner(s).
Humidity is typically measured as relative humidity (RH). RH is a percentage value that indicates the amount of moisture in the air relative to the maximum amount the air can hold at a given temperature. Cold air is able to hold less moisture than warm air; hence, the air is dry during the winter and humid in the summer.
Return On Investment
A performance measure used to evaluate the efficiency of an investment or to compare the efficiency of a number of different investments. Also referred to as ROI. In terms of real estate ROI, refinishing a basement instantly and easily adds a significant amount of living space with even a simple basement remodel.
Also referred to as a “band joist”. A rim joist rests on the sill or sill plate functioning to keep the joists true also providing a surface for completing the edge of subflooring and a flat base to support the exterior walls. The rim joist is the “box” of a floor’s structure.
Iron oxide that forms when exposed to oxygen and moisture.
The process of removing paint from a masonry wall using a dustless system.
A sill plate, or sole plate, in construction is the bottom horizontal member of a wall or building to which vertical members are attached. Sill plates are usually 2×4 lumber. In the platform framing method the sill plate is anchored to the foundation wall. The bottom of the sill plate is ideally kept 6 inches above the finished grade.
Sill Plate Bracket
The bracket used to attach Carbon Fiber to sill plate.
Substrate particles smaller than sand and larger than clay.
A solid concrete structure. Typically, slabs are installed as ceilings over cold cellars as well as over a gravel base for the construction of basement and garage floors.
Refers to the wetness of concrete when delivered, slump is measured on a scale of 1 to 12 with 1 being the driest mix.
A rod which is used to hold concrete forms in place when building a poured concrete foundation. It is called a snap rod because, once the concrete has cured and the forms have been removed, the protruding rods are snapped off (usually with a hammer); thus providing a smooth concrete surface.
Expansive soils contain minerals such as smectite clays that are capable of absorbing water. When they absorb water they increase in volume. The more water they absorb the more their volume increases. Expansions of ten percent or more are not uncommon. This change in volume can exert enough force on a building or other structure to cause damage.
The chipping, splintering, and breaking into smaller pieces of poured concrete, concrete blocks or cinderblocks, bricks, and stone. Spalling usually occurs when water that has permeated pourous materials freezes and causes surface deterioration.
To produce or release spores.
A term that refers to the way air moves throughout a home. Due to the upward movement of warm air in a home, a vacuum is created in the lower levels. If a basement or crawl space is infested with mold or other unpleasant airborne pollutants and allergens, they are then pulled upwards into the home along with the air.
The most common type of wall support on the market the uses a 13 lb steel H beam concreted into the floor and framed into the floor joists above.
A sump pump is a pump used to remove water that has accumulated in a sump pit. A sump pit, commonly found in the home basement, is simply a hole to collect water. A pump used to mechanically evacuate water that has accumulated in a sump pit or liner, usually found beneath the floor in the basement of homes. The water may enter the sump pit via the perimeter drains of a basement waterproofing system such as weeping tile or an internal de-watering system, or if the basement is below the level of the local water table. Sump pumps are also used where basement flooding happens regularly and to protect against dampness where the water table is high relative to the footing of a home. Sump pumps mechanically pump water away from a house to any place where it is no longer problematic, such as a municipal storm drain or a dry well, or to the outside. In older homes, sump pumps may be connected to the sanitary sewer. Currently, this practice is not in conformance with the plumbing code and/or municipal bylaws because the volume of water coming from sump pits can overwhelm the municipal storm drain system. Powered by a home’s electrical system, sump pumps can be supplemented by a battery backup. Since a sump pit may overflow if not constantly pumped, a backup system is important for cases when the main power is out for prolonged periods of time, also, the sump pump can corrode from evaporating water in the sump pit; if a motor does not operate frequently, it is advisable to cause the motor to run at least every 3 months. There are two types of sump pumps: pedestal and submersible. The pedestal pump’s motor is mounted above the pit, where it is more easily serviced but also more conspicuous. The submersible pump is entirely mounted inside the pit, and is specially sealed to prevent electrical short circuits.
Repair of a concrete surface that constitutes only a small portion of the depth of a member or element.
A phenomenon caused by the attraction of molecules to like molecules. As molecules on the liquid surface are not surrounded by the same molecules on all sides, there is a resultant increase in their attraction to neighboring molecules on a surface.
A shallow troughlike depression that carries water mainly during rainstorms or snow melts.
A viscous black liquid containing numerous organic compounds that is obtained by the destructive distillation of coal and used for roofing and waterproofing.
A hole left by the removal of a metal rod which is used to hold concrete forms in place when building a poured concrete foundation. Typically spaced 18″ apart at a height of 2′ and 5′, tie-rod holes are approximately ¾” in diameter. To ensure that water does not penetrate a foundation, tie-rod holes are usually covered, on both the inside and outside of the foundation, with a concrete patch.
The visual display of the amount of infrared energy emitted by an object using a specialized camera. This is commonly used for leak detection in building structures. See also “Infrared thermography”.
Paste used to anchor epoxy injection T-ports to the wall which acquires a lower viscosity when mechanically agitated, and rapidly stiffens upon subsequent rest; a material having this property can be placed vertically or horizontally without sagging during the curing process. This is the type of paste used for epoxy crack injections.
Also referred to as “repointing”, involves the placement of wet mortar into cut or raked joints for the repair of weathered joints in old or damaged masonry.
To dig or wear away the base or foundation.
A barrier used to prevent water vapor diffusion; a vapor barrier is typically used to isolate wooden or steel framing from the concrete on which it rests.
A thin and usually jagged space opened in a previously solid material.
If the inward bowing of a basement wall is not excessive, walls damaged by excessive inward pressures may often be repaired by excavating behind the wall, allowing the wall to flex back into vertical position. If the inward bowing of the wall is excessive, the wall requires replacement. The foundation drainage system will also require replacement at that time. The details for these repairs may be determined by a qualified and experienced contractor or a structural engineer.
Movement of a basement wall due to outside pressure that eventually cause the bottom of the wall to slide over the foundation floor. This is most common in concrete block walls.
Wall Tie Backs
A solution for repairing bowed walls using an interior wall plate, an exterior earth anchor and a connecting steel rod to stabilize foundation walls.
To let water or other fluid in or out through a hole, crevice, etc.
Treatment of the surface or structure to prevent the passage of water through the building envelope under hydrostatic pressures. Waterproofing provides a full and continuous barrier to water penetration.
Water oozed through a porous material or soil. The act or process of seeping; percolation.
The level below which the ground is completely saturated with water. Also called water level. It is also known to be the depth at which soil pore spaces or fractures and voids in rock become completely saturated with water.
A porous or perforated pipe used for underground drainage. Weeping tile is installed along the foundation footings exposed to the water table.
The flow of moisture through the small interconnected pores in concrete due to adhesion and surface tension.
Typically a galvanized steel semi-circular structure installed to prevent the cave-in of soil and water flow into below grade basement windows.
Window Well Drain
A drain, similar to a kitchen sink drain, which channels window well water towards the weeping tile and its surrounding gravel layer. A window well drain prevents water from entering a basement from around the window frame or through the window itself.